CN 8501
Electric motors and generators (excluding generating sets)
| Code | Description | Unit | Third-country duty | Source |
|---|---|---|---|---|
| 8501 10 | Motors of an output not exceeding 37,5 W | TARIC | ||
| 8501 10 10 | Synchronous motors of an output not exceeding 18 W | TARIC | ||
| 8501 10 10 10 | For use in certain types of aircraft | p/st | 4.7% | TARIC |
| 8501 10 10 20 | Synchronous motor for a dishwasher with a water flow control mechanism with - a length without axle of 24 mm (+/- 0,3), - a diameter of 49,3 mm (+/- 0,3) - a rated voltage of 220 V AC or more but not more than 240 V AC, - a rated frequency of 50 Hz or more but not more than 60 Hz, - an input power of not more than 4 W, - a rotation speed of 4rpm or more but not more than 4,8rpm, - an output torque of not less than 10kgf/cm | p/st | 4.7% | TARIC |
| 8501 10 10 40 | Synchronous hybrid stepper motor with: -an output not exceeding 18 W, -two phases, -a rated current of not more than 2,5 A/phase, -a rated voltage of not more than 20 V, -with or without a threaded shaft, for use in the manufacture of 3D printers | p/st | 4.7% | TARIC |
| 8501 10 10 50 | Linear actuator for automotive electric seat adjustment applications: -consisting of a permanently excited DC motor with an integrated gear mechanism and leadscrew, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with Hall Effect Sensor, -with a nominal voltage of 8 V or higher but not higher than 16 V, -with a rated output mechanical power not exceeding 20 W, and -with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car's seats | p/st | 4.7% | TARIC |
| 8501 10 10 60 | Rotary actuator for automotive electric seat adjustment applications: -consisting of a permanently excited DC motor with an integrated gear mechanism, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with Hall Effect Sensor, -with a nominal voltage of 8 V or more but not more than 16 V, -with a rated output mechanical power not exceeding 35 W, and -with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car's seats | p/st | 4.7% | TARIC |
| 8501 10 10 90 | Other | p/st | 4.7% | TARIC |
| Other | ||||
| 8501 10 91 | Universal AC/DC motors | TARIC | ||
| 8501 10 91 10 | For use in certain types of aircraft | p/st | 2.7% | TARIC |
| 8501 10 91 90 | Other | p/st | 2.7% | TARIC |
| 8501 10 93 | AC motors | TARIC | ||
| 8501 10 93 10 | For use in certain types of aircraft | p/st | 2.7% | TARIC |
| 8501 10 93 90 | Other | p/st | 2.7% | TARIC |
| 8501 10 99 | DC motors | TARIC | ||
| 8501 10 99 10 | For use in certain types of aircraft | p/st | 2.7% | TARIC |
| Other | ||||
| 8501 10 99 20 | Worm axis motor for automotive electric seat adjustment applications: -consisting of a permanently excited DC motor with a worm wheel, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with Hall Effect Sensor, -with a nominal voltage of 8 V or more but not more than 16 V, -with a rated output mechanical power not exceeding 35 W, and -with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car's seats | p/st | 2.7% | TARIC |
| 8501 10 99 30 | Linear actuator for automotive electric seat adjustment applications: -consisting of a permanently excited DC motor with an integrated gear mechanism and leadscrew, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with Hall Effect Sensor, -with a nominal voltage of 8 V or higher but not higher than 16 V, -with a rated output mechanical power not exceeding 20 W, and -with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car's seats | p/st | 2.7% | TARIC |
| 8501 10 99 40 | Rotary actuator for automotive electric seat adjustment applications: -consisting of a permanently excited DC motor with an integrated gear mechanism, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with Hall Effect Sensor, -with a nominal voltage of 8 V or more but not more than 16 V, -with a rated output mechanical power not exceeding 35 W, and -with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car's seats | p/st | 2.7% | TARIC |
| 8501 10 99 50 | Electric (DC) motor powering height adjusting with: -a rated output mechanical power not exceeding 35 W, -frame integration with a length of 156 mm, a height of 59 mm, a thickness of 36 mm and a weight of 500 g, -a stall torque of 45 Nm and ultimate torque of 200 Nm, -a maximum current of 15 A, -no load speed of 7 RPM or more but not more than 10 RPM, -a rotation speed of 4 000 RPM or more but not more than 5 600 RPM, -a maximum noise level of 42 dB(A), -a maximum angular backlash up to 3 degrees, and -a 8 tooth pinion module, for use in the manufacture of automotive components for car's seats | p/st | 2.7% | TARIC |
| 8501 10 99 56 | DC Motor: - with a speed rotation of not more than 7 000 rpm without load, - with a nominal voltage of not more than 18 V, - with a maximum power of 24 W, - for a specific temperature range from -40°C to 160°C, - with or without a gear connection, - with or without a mechanical attachment interface, - with 2 electrical connections, - with a maximum torque of 100 Nm | p/st | 2.7% | TARIC |
| 8501 10 99 58 | DC Motor : - with a speed rotation of not more than 6500 rpm (without load), - with a nominal voltage of 12 V (± 4 V), - with a maximal power below than 20 W, - with a specified temperature range from -40°C to 160°C, - with a worm gear drive, - with a mechanical attachment interface, - with 2 electrical connections, - with a maximum torque of 75 Nm | p/st | 2.7% | TARIC |
| 8501 10 99 60 | DC motor - with a rotor speed of 3 500 rpm or more but not more than 5 000 rpm loaded and not more than 6 500 rpm when not loaded - with a power supply voltage of 100 V or more but not more than 240 V for use in the manufacture of electric fryers | p/st | 2.7% | TARIC |
| 8501 10 99 64 | DC motor to control angular position of the flap to adjust gas flow in the Air Throttle and EGR valve: -with Ingress Protection (IP) standard of IP69, -with a rotor speed of not more than 6 500 rpm when not loaded, -with a rated voltage of 12,0 V (± 0,1), -of a specified temperature range of - 40 °C or more but not more than 165 °C, -with or without a connecting pinion, -with or without an engine connector, -with or without a flange, -with a diameter of not more than 40 mm (not including the flange), -with an overall height of not more than 90 mm (from the base to the pinion) | p/st | 2.7% | TARIC |
| 8501 10 99 65 | Electric turbocharger actuator, with: - a DC motor, - an integrated gear mechanism, - a (pulling)force of 200 N or more at a minimum of 140°C elevated ambient temperature, - a (pulling) force of 250 N or more in each position of its stroke, - an effective stroke of 15 mm or more but not more than 25 mm, - with or without an on-board diagnostics interface | p/st | 2.7% | TARIC |
| 8501 10 99 70 | DC stepping motor, with - a two-phase winding, - a rated voltage of 9 V or more, but not more than 16,0 V - of a specified temperature range covering at least - 40 °C to + 105 °C - with or without connecting pinion - with or without motor drive connector | p/st | 2.7% | TARIC |
| 8501 10 99 75 | Permanently excited DC motor with - a multiple-phase winding, - an external diameter of 24 mm or more but not more than 38 mm, - a rated speed of not more than 12 000 rpm, - a power supply voltage of 8 V or more but not more than 27 V, - with or without a pulley, - with or without a gear wheel | p/st | 2.7% | TARIC |
| 8501 10 99 79 | DC motor with brushes and an internal rotor with a three-phase winding, whether or not equipped with a worm or a pinion, of a specified temperature range covering at least - 20°C to + 70°C | p/st | 2.7% | TARIC |
| 8501 10 99 90 | Other | p/st | 2.7% | TARIC |
| 8501 20 | Universal AC/DC motors of an output exceeding 37,5 W | TARIC | ||
| 8501 20 00 10 | Of an output exceeding 735 W but not exceeding 150 kW, for use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 20 00 20 | Of an output of less than 750 W or exceeding 150 kW, for use in certain types of aircraft | p/st | 2.7% | TARIC |
| 8501 20 00 50 | Universal AC/DC motor, rotating: -with a nominal supply voltage of 230 V, -with a power of more than 37,5 W but not more than 2 000 W, -with a stator cross-section of 93 mm or more but not more than 103 mm and a thickness of 15 mm or more but not more than 45 mm, and -with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliances | p/st | 2.7% | TARIC |
| 8501 20 00 60 | Universal AC/DC motor, rotating: -with a nominal supply voltage of 230 V, -with a power of more than 37,5 W but not more than 1 200 W, -with a stator cross-section of 65 mm or more but not more than 75 mm and a thickness of 15 mm or more but not more than 45 mm, and -with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliances | p/st | 2.7% | TARIC |
| 8501 20 00 70 | Universal AC/DC motor, rotating: -with a nominal supply voltage of 230 V, -with a power of more than 37,5 W but not more than 700 W, -with a stator cross-section of 49 mm or more but not more than 59 mm and a thickness of 15 mm or more but not more than 45mm, and -with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliances | p/st | 2.7% | TARIC |
| 8501 20 00 90 | Other | p/st | 2.7% | TARIC |
| Other DC motors; DC generators, other than photovoltaic generators | ||||
| 8501 31 | Of an output not exceeding 750 W | TARIC | ||
| 8501 31 00 10 | Motors of an output exceeding 735 W, DC generators, for use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 31 00 20 | For use in certain types of aircraft | p/st | 2.7% | TARIC |
| Other | ||||
| 8501 31 00 45 | DC motors, brushless, with: - an external diameter of 90 mm or more, but not more than 110 mm, - a rated speed of not more than 3 680 rpm, - an output of 600 W or more but not more than 740 W at 2 300 rpm and at 80 °C, - a supply voltage of 12 V, - a torque of not more than 5,67 Nm, - a rotor position sensor, - an electronic star-point relay, and - for use with an electric power steering control module | p/st | 2.7% | TARIC |
| 8501 31 00 47 | Motor for automotive electric seat adjustment applications: -with a shaft output on both motor sides, -consisting of a permanently excited DC motor, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with Hall Effect Sensor, -with a nominal voltage of 8 V or more but not more than 16 V, -with a rated output mechanical power not exceeding 120 W, and -with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car's seats | p/st | 2.7% | TARIC |
| 8501 31 00 48 | Brushless DC electric motors: -with a rated power of 240 W or more, but not more than 260 W, -with a voltage of 36 V or higher, but not higher than 52 V -with a torque of 20 Nm or more, but not more than 140 Nm, -with a housing made of aluminum, aluminum alloy or plastic, -with or without a built-in controller, -with a communication function in the LIN or UART interface, -weighing 1,5 kg or more, but not more than 5,0 kg, -adapted for mounting in a bicycle frame for use in the manufacture of e-bikes | p/st | 2.7% | TARIC |
| 8501 31 00 49 | Brushless DC electric motors: - with a rated power of 240 W or more, but not more than 260 W, - with a voltage of 24 V or higher, but not higher than 52 V, - with a torque of 30 Nm or more, but not more than 62 Nm, - with a LIN, UART or CAN communication interface, - with an internal planetary gearbox with fixed or variable ratio or direct drive, - with a housing made of aluminum or aluminium alloy, - with a weight of 1,5kg or more, but not more than 6kg, - adapted for mounting in the front or rear bicycle wheel, for use in the manufacture of e-bikes | p/st | 2.7% | TARIC |
| 8501 31 00 50 | DC motors, brushless, with: - an external diameter of 80 mm or more, but not more than 200 mm, - a supply voltage of 4 V or more, but not more than 16 V, - an output at 20 °C of 200 W or more, but not more than 750 W, - a torque at 20 °C of 2,00 Nm or more, but not more than 7,00 Nm, - a rated speed at 20 °C of 600 rpm or more, but not more than 3 100 rpm, - with or without a pulley, - with or without an electronic power steering sensor/controller | p/st | 2.7% | TARIC |
| 8501 31 00 52 | Electric brushless direct current motor finished with biocompatible materials such as stainless steel according to specification 17-4 PH or type 303, 316L, 400 with: -a three-phase winding, -an output power not exceeding 280 W, -a length with gearhead of 116,1 mm or more but not more than 117,2 mm, -an external diameter of 13,86 mm or more but no more than 13,92 mm, -a maximum torque of motor with gearhead 246,6 mNm in 25℃, -a no-load radial speed of motor with gearhead with 9 900 rpm, at 24V in 25°C, -a weight of motor with gearhead of 70,5 g or more but not more than 71,5 g, a resistance to peak temperature of 140°C or more (non-operating), a maximal air leak between shaft and shaft seals of 15 Pa/s at given 2 Bars of pressure, -14 functional pins for power and control purpose, -a flexible printed circuit with length of 245 mm but no longer than 255 mm with mounted 8 pin male connector for use in the manufacture of medical devices with right-left rotation and oscillation function | p/st | 2.7% | TARIC |
| 8501 31 00 54 | Brushless DC electric motor, with: -a rated voltage of 310 V, -a rated power of 350 W or more but not more than 368 W, -an input power of 500 W or more but not more than 550 W, -output power of 350 W or more but not more than 400 W, -an external diameter without bracket connector and pulley of 143,2 mm or more but not more than 143,8 mm, -a rated speed of 16300 rpm or more but not more than 16500 rpm, -a weight of 2,33 kg or more but not more than 2,40 kg, -a pulley | p/st | 2.7% | TARIC |
| 8501 31 00 55 | DC motor with or without commutator, for driving hand-held power tools, lawn mowers or home appliances, with: -an external diameter of 24,2 mm or more, but not more than 140 mm, -a rated speed of 3300 rpm or more, but not more than 26200 rpm, -a rated supply voltage of 3,6 V or more, but not more than 230 V, -an output power of more than 37,5 W , but not more than 2400 W, -a free load current of not more than 20,1 A, -a maximum efficiency of 50 % or more, | p/st | 2.7% | TARIC |
| 8501 31 00 56 | DC motor, brushless, integrated with an Electronic Control Unit (ECU), defined as a Power Pack with: -a safety feature and mechanism designed for prevention of critical hazards like self-steer by single failure, -a CAN-communication interface, -an external sensor interface, -operating temperature range of -40℃ to 95℃ or broader, -compliance with standard IP6K9K for water and dustproofness, -supply voltage of 9 V or more, but not more than 16 V, -rated power output of 500 W or more, but not higher than 750 W, -rated torque of 3 Nm or more, but not more than 6 Nm, -length of 150 mm or more, but not more than 250 mm, -width of 100 mm or more, but not more than 150 mm, -height of 80 mm or more, but not more than 120 mm | p/st | 2.7% | TARIC |
| 8501 31 00 57 | Brushless DC electric motor with LCD control indicator and/or control unit with buttons: -with an output power of 200 W or more, but not more than 700 W, -with a supply voltage of 30 V or more, but not more than 60 V, -with a torque of 30 Nm or more, but not more than 200 Nm, -with a height of 117 mm or more, but not more than 146 mm, -with a length of 117 mm or more, but not more than 223 mm, -with a width of 135 mm or more, but not more than 190 mm, -with a weight of 2 kg or more but not more than 5 kg, -designed to be mounted in a frame, front or rear bicycle wheel, -equipped with sockets, at least for cable connection with LCD control indicator, for use in the manufacture of electric bicycles | p/st | 2.7% | TARIC |
| 8501 31 00 58 | Permanently excited DC motor with: -an external diameter of 27 mm or more but not more than 90 mm, including mounting flange, -a rated speed of not more than 25 000 rpm, -an output of 45 W or more but not more than 400 W, and -a supply voltage of 9 V or more but not more than 50 V, -whether or not a multiple-phase winding, -whether or not with a drive disc, -whether or not with a crankcase, -whether or not with a fan, -whether or not with a cap assembly, -whether or not with a sun gear, -whether or not with a speed and rotational direction encoder, -whether or not with or without a speed or rotational direction sensor of resolver type or Hall effect type, -whether or not with a mounting flange for use in the manufacture of air suspension seats in tractors, earthmoving machines and forklifts or for use in the manufacture of actuators for height-adjustable furniture | p/st | 2.7% | TARIC |
| 8501 31 00 63 | Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: - a specified speed of not more than 6000rpm, - a minimum output of 400W, but not more than 1,3kW (at 12 V), or with a minimum output of 750W but not more than 1,55kW (at 36 V), - a flange diameter of 85mm or more but not more than 200mm, - a maximum length of 335mm, measured from the beginning of the shaft to the outer ending, - a housing length of not more than 265mm, measured from the flange to the outer ending, - a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), - a stator with single T-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and - surface magnets, - whether or not with electronic power steering controller, - whether or not with pulley or coupling, - whether or not with rotor position sensor | p/st | 2.7% | TARIC |
| 8501 31 00 68 | Camshaft actuator for controlling the timing of valve opening by using electromotor in a continuous variable valve timing system of an internal combustion piston engine, of: -a length of 110 mm or more but not more than 140 mm, -a width of 90 mm or more but not more than 130 mm, -a height of 80 mm or more but not more than 110 mm for use in the manufacture of engines of motor vehicles | p/st | 2.7% | TARIC |
| 8501 31 00 85 | Power transmission device for controlling the output of exhaust gas turbochargers, consisting of: - a DC motor of an output not exceeding 600 W, - for usage with a supply voltage of 8 V or more but no more than 48 V, - with motor connection (plug-in connection), - whether or not with position sensor, - whether or not with integrated control and power electronics, - whether or not with spring mechanism for resetting the lever, - built in a housing with reduction gear and lever attached to the motor drive shaft, or - built in a housing with threads integrated into the rotor of the motor for linear movement of the integrated control rod | p/st | 2.7% | TARIC |
| 8501 31 00 99 | Other | p/st | 2.7% | TARIC |
| 8501 32 | Of an output exceeding 750 W but not exceeding 75 kW | TARIC | ||
| 8501 32 00 10 | For use in civil aircraft | p/st | 0% (end-use) | TARIC |
| Other | ||||
| 8501 32 00 40 | DC motor with or without commutator, for driving hand-held power tools, lawn mowers or home appliances, with: -an external diameter of 24,2 mm or more, but not more than 140 mm, -a rated speed of 3300 rpm or more, but not more than 26200 rpm, -a rated supply voltage of 3,6 V or more, but not more than 230 V, -an output power of more than 37,5 W , but not more than 2400 W, -a free load current of not more than 20,1 A, -a maximum efficiency of 50 % or more, | p/st | 2.7% | TARIC |
| 8501 32 00 65 | Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: - a specified speed of not more than 6000rpm, - a minimum output of 400W, but not more than 1,3kW (at 12 V), or with a minimum output of 750W but not more than 1,55kW (at 36 V), - a flange diameter of 85mm or more but not more than 200mm, - a maximum length of 335mm, measured from the beginning of the shaft to the outer ending, - a housing length of not more than 265mm, measured from the flange to the outer ending, - a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), - a stator with single T-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and - surface magnets, - whether or not with electronic power steering controller, - whether or not with pulley or coupling, - whether or not with rotor position sensor | p/st | 2.7% | TARIC |
| 8501 32 00 99 | Other | p/st | 2.7% | TARIC |
| 8501 33 | Of an output exceeding 75 kW but not exceeding 375 kW | TARIC | ||
| 8501 33 10 00 | Hydrogen fuel cell generators | p/st | 2.7% | TARIC |
| 8501 33 90 | Other | TARIC | ||
| 8501 33 90 10 | Motors of an output not exceeding 150 kW and generators, for use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 33 90 20 | Of an output exceding 150 kW, for use in certain types of aircraft | p/st | 2.7% | TARIC |
| 8501 33 90 30 | Electric drive for motor vehicles, with an output of not more than 315 kW: -with an AC or DC motor with or without transmission, -with or without power electronics | p/st | 2.7% | TARIC |
| 8501 33 90 99 | Other | p/st | 2.7% | TARIC |
| 8501 34 | Of an output exceeding 375 kW | TARIC | ||
| 8501 34 00 10 | Generators for use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 34 00 99 | Other | p/st | 2.7% | TARIC |
| 8501 40 | Other AC motors, single-phase | TARIC | ||
| 8501 40 20 | Of an output not exceeding 750 W | TARIC | ||
| 8501 40 20 10 | Of an output exceeding 735 W, for use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 40 20 20 | For use in certain types of aircraft | p/st | 2.7% | TARIC |
| 8501 40 20 35 | Electric AC motor, single-phase, with: -a rated power of 120 W or more but not more than 150 W, -an input power of 280 W or more but not more than 350 W, -an external diameter without bracket connector and pulley of 145 mm or more but not more than 160 mm, -a rated speed of 2 680 rpm or more but not more than 3 000 rpm, -a weight of 4,2 kg or more but not more than 4,6 kg, -pulleys, a spindle and a tachometer, for use in the manufacture of home appliance products | p/st | 2.7% | TARIC |
| 8501 40 20 45 | Electric AC motor, single-phase, with: -a rated power of 275 W or more, but not more than 325 W, -an input power of 600 W or more but not more than 700 W, -an external diameter without bracket and connector of 150 mm or more but not more than 170 mm, -a rated speed of 15 000 rpm or more but not more than 20 000 rpm, -a weight of 4,2 kg or more, -a pulley and a tachometer, for use in the manufacture of home appliance products | p/st | 2.7% | TARIC |
| 8501 40 20 50 | Electric AC motor, single-phase, with: -a rated power of 300 W or more but not more than 370 W, -an input power of 600 W or more but not more than 700 W, -an external diameter without bracket and connector of 150 mm or more but not more than 170 mm, -a rated speed of 15 000 rpm or more but not more than 19 000 rpm, -a weight of 4,8 kg or more, -a pulley, for use in the manufacture of home appliance products | p/st | 2.7% | TARIC |
| 8501 40 20 55 | Electric AC motor, single-phase, with: -a rated power of 275 W or more, but not more than 325 W, -an input power of 600 W or more but not more than 700 W, -an external diameter without bracket and connector of 160 mm or more but not more than 180 mm, -a rated speed of 15 000 rpm or more but not more than 19 000 rpm, -a weight of not more than 4,4 kg, -a pulley, for use in the manufacture of home appliance products | p/st | 2.7% | TARIC |
| 8501 40 20 60 | Electric AC motor, single-phase, with: -a rated power of 275 W or more but not more than 325 W, -an output power of 550 W or more but not more than 600 W, -an input power of 800 W or more but not more than 1 000 W, -an external diameter of more than 150 mm but not more than 170 mm without the bracket, -a rated speed of more than 16 000 rpm but not more than 18 000 rpm, -a weight of 3,4 kg or more but not more than 3,7 kg, -a pulley, for use in the manufacture of home appliance products | p/st | 2.7% | TARIC |
| 8501 40 20 70 | Electric AC motor, single-phase, whether or not with commutator - with a nominal output of 180 W or more, - with an input power of 150 W or more but not more than 2 700 W, - with an external diameter of more than 44,8 but not more than 135,2 mm, - with a rated speed of more than 10 000 rpm but not more than 50 000 rpm, - whether or not equipped with air-inducting ventilator, - whether or not with mechanical device (pinion, screws, gear connection etc.) on the shaft, for use in the manufacture of domestic appliances | p/st | 2.7% | TARIC |
| 8501 40 20 75 | Incomplete, single-phase brushless AC motor consisting of a rotor and a stator: -a rotor on the inside is equipped with a ring of 12 magnets housed in a steel casing, -a stator with an internal diameter of 206,6 mm (± 0,5 mm), external diameter of 265,0 mm (± 0,2 mm) and width of 37,2 mm or more but not more than 47,8 mm, -with a rated power not exceeding 750 W, -with a weight of 5 kg or more, for use in the production of washing machines, washer-dryers equipped with a drum with direct drive | p/st | 2.7% | TARIC |
| 8501 40 20 80 | Other | p/st | 2.7% | TARIC |
| 8501 40 80 | Of an output exceeding 750 W | TARIC | ||
| 8501 40 80 10 | Of an output not exceeding 150 kW, for use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 40 80 20 | Of an output exceeding 150 kW, for use in certain types of aircraft | p/st | 2.7% | TARIC |
| 8501 40 80 50 | Electric drive for motor vehicles, with an output of not more than 315 kW: -with an AC or DC motor with or without transmission, -with or without power electronics | p/st | 2.7% | TARIC |
| 8501 40 80 70 | Electric AC motor, single-phase, whether or not with commutator - with a nominal output of 180 W or more, - with an input power of 150 W or more but not more than 2 700 W, - with an external diameter of more than 44,8 but not more than 135,2 mm, - with a rated speed of more than 10 000 rpm but not more than 50 000 rpm, - whether or not equipped with air-inducting ventilator, - whether or not with mechanical device (pinion, screws, gear connection etc.) on the shaft, for use in the manufacture of domestic appliances | p/st | 2.7% | TARIC |
| 8501 40 80 90 | Other | p/st | 2.7% | TARIC |
| Other AC motors, multi-phase | ||||
| 8501 51 | Of an output not exceeding 750 W | TARIC | ||
| 8501 51 00 10 | Of an output exceeding 735 W, for use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 51 00 20 | Of an output of less than 750 W, for use in certain types of aircraft | p/st | 2.7% | TARIC |
| 8501 51 00 25 | Electric permanent magnet synchronous motor with: -an output power of 550 W, -a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron (per GB/T 13560 standard) enclosed in polyethylene cover, -an outer diameter of motor magnet shaft end with dimension of 10,001 mm or more but no more than 10,007 mm, -terminals located across the radius 32,5 mm and separated by an angle of 21,8°, -a motor housing made of ADC12 or AC46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per JIS H5302 or EN1706 standard), -a back electromotive force constant (Ke) of 0,03306 V-sec/rad or more but no more than 0,03654 V-sec/rad, -a back electromotive force harmonic order - 5th of no more than 0,38 % (of fundamental) and 7th of no more than 0,25 % (of fundamental), -a cogging torque of no more than 13 mNm, -a friction torque in ambient temperature of no more than 22 mNm, -a maximum temperature of motor operation of no more than 200 °C | p/st | 2.7% | TARIC |
| 8501 51 00 30 | AC synchronous servo motor with resolver and brake for a maximum speed of not more than 6 000rpm,With: - an output of 340W or more but not more than 7,4kW, - a flange of dimensions of not more than 180mm × 180mm, and - a length from flange to extreme end of resolver of not more than 271mm | p/st | 2.7% | TARIC |
| 8501 51 00 35 | Electric permanent magnet synchronous motor with: -an output power of 600 W, -a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron and dysprosium enclosed in aluminium cover, -an outer diameter of motor magnet shaft end with dimension of 10,001 mm or more but no more than 10,007 mm, -terminals located across the diameter 59,2 mm and separated by an angle 30,0°, -a housing made of electrogalvanized steel (per JIS G3313 Grade SECE standard) using a deep-drawing stamping process, -a diameter of 88,600 mm or less but no less than 88,546 mm at the motor-system assembly interface, -a back electromotive force constant (Ke) of 0,03277 V-sec/rad or more but no more than 0,03623 V-sec/rad, -a back electromotive force harmonic order - 5th of no more than 0,35 % (of fundamental) and 7th of no more than 0,30 % (of fundamental), -a cogging torque of no more than 12 mNm, -a friction torque in ambient temperature of no more than 23 mNm, -a maximum temperature of motor operation of no more than 200 °C | p/st | 2.7% | TARIC |
| 8501 51 00 40 | Electric AC motor, three-phase, with: -a rated power of 280 W or more but not more than 320 W, -an output power of 480 W or more but not more than 540 W, -an input power of 800 W or more but not more than 900 W, -an external diameter of 150 mm or more but not more than 170 mm, -a rated speed of 15 000 rpm or more but not more than 20 000 rpm, -a weight of 6 kg or more but not more than 6,4 kg, -a pulley and a tachometer, for use in the manufacture of home appliance products | p/st | 2.7% | TARIC |
| 8501 51 00 45 | Automotive-ready brushless permanently excited magnet synchronous alternating current motor with: -a specified speed of not more than 7000 rpm, -an output of 400 W or more but not more than 750 W (at 12 V), -a flange diameter of 80 mm or more, but not more than 200 mm, -a maximum length of not more than 335 mm, measured from the beginning of the shaft to its outer end, -a housing length of not more than 265 mm, measured from the flange to the outer end, -a steel sheet or die-cast aluminium basic housing consisting of not more than two parts, including electrical components and a flange with two or more but not more than 11 holes, whether or not with a sealing connection (groove with O-ring and protective grease or liquid seal interface), -a stator with single T-tooth design and single coil winding with 9/6 or 12/10 or 12/8 topology and surface magnets, -whether or not with electronic power steering controller, -whether or not with pulley or coupling, -whether or not with rotor position sensor | p/st | 2.7% | TARIC |
| 8501 51 00 50 | Three phase AC synchronous brushless permanent magnet motor with: -an output of 500 W or more but not more than 700 W, -an external diameter of 129,7 mm or more but not more than 180,3 mm, -a rated speed of 16 000 rpm or more but not more than 17 000 rpm, -a weight of 2,5 kg or more but not more than 3,1 kg, and -with a pulley, for use in the manufacture of home appliance products | p/st | 2.7% | TARIC |
| 8501 51 00 90 | Other | p/st | 2.7% | TARIC |
| 8501 52 | Of an output exceeding 750 W but not exceeding 75 kW | TARIC | ||
| 8501 52 20 | Of an output exceeding 750 W but not exceeding 7,5 kW | TARIC | ||
| 8501 52 20 10 | For use in civil aircraft | p/st | 0% (end-use) | TARIC |
| Other | ||||
| 8501 52 20 50 | AC synchronous servo motor with resolver and brake for a maximum speed of not more than 6 000rpm,With: - an output of 340W or more but not more than 7,4kW, - a flange of dimensions of not more than 180mm × 180mm, and - a length from flange to extreme end of resolver of not more than 271mm | p/st | 2.7% | TARIC |
| 8501 52 20 55 | Brushless synchronous alternating current electric motors with permanent magnets, with: -an output power of 1000 W or more, but not more than 1400 W, -a rotor containing 8 poles, generated by permanent magnets composed mainly of praseodymium-neodymium-iron-boron (GB/T 13560-2017 standard), enclosed in a stainless steel cover, -a motor magnet shaft end outer diameter of 10,001 mm or more, but not more than 10,007 mm, -motor terminals located across the 37,00 mm radius and separated by an angle of 30,00 °, -a motor housing made of ADC12 or EN AC46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per JIS H5302-2000 or EN 1706 standard), -a back electromotive force constant (Ke) of 0,0265 V-sec/rad or more, but not more than 0,0293 V- sec/rad, -a back electromotive force (EMF) harmonic order - 5th of no more than 0,4 % (of fundamental) and 7th of no more than 0,2 % (of fundamental), -a synchronous inductance of 33,49 µH or more, but not more than 37,01 µH, -a cogging torque of not more than 15 mNm, -a friction torque in ambient temperature of not more than 20 mNm, -a maximum motor operation temperature of not more than 200 °C, -with or without a spline on the motor shaft | p/st | 2.7% | TARIC |
| 8501 52 20 70 | Automotive-ready brushless permanently excited magnet synchronous alternating current motor with: -a specified speed of not more than 7000 rpm, -an output of 750 W or more but not more than 1,8 kW (at 12 V), -a flange diameter of 80 mm or more, but not more than 200 mm, -a maximum length of not more than 335 mm, measured from the beginning of the shaft to its outer end, -a housing length of not more than 265 mm, measured from the flange to the outer end, -a steel sheet or die-cast aluminium basic housing consisting of not more than two parts, including electrical components and a flange with two or more but not more than 11 holes, whether or not with a sealing connection (groove with O-ring and protective grease or liquid seal interface), -a stator with single T-tooth design and single coil winding with 9/6 or 12/10 or 12/8 topology and surface magnets, -whether or not with electronic power steering controller, -whether or not with pulley or coupling, -whether or not with rotor position sensor | p/st | 2.7% | TARIC |
| 8501 52 20 80 | Electric permanent magnet synchronous motor with: -an output power of 850 W, -a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron (per GB/T 13560 standard) enclosed in polyethylene cover, -an outer diameter of motor magnet shaft end with dimension of 10,001 mm or more but no more than 10,007 mm, -terminals located across the radius 26,2 mm and separated by an angle 30,0°, -a housing made of ADC12 or AC46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per JIS H5302 or EN1706 standard) and anodized coating (per ASTM B580 type E standard), -a back electromotive force constant (Ke) of 0,04009 V-sec/rad or more but no more than 0,04431 V-sec/rad, -a back electromotive force harmonic order - 5th of no more than 0,36 % (of fundamental) and 7th of no more than 0,24 % (of fundamental), -a cogging torque of no more than 20 mNm, -a friction torque in ambient temperature of no more than 26,5 mNm, -a maximum temperature of motor operation of no more than 200 °C | p/st | 2.7% | TARIC |
| 8501 52 20 89 | Other | p/st | 2.7% | TARIC |
| 8501 52 30 | Of an output exceeding 7,5 kW but not exceeding 37 kW | TARIC | ||
| 8501 52 30 10 | For use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 52 30 90 | Other | p/st | 2.7% | TARIC |
| 8501 52 90 | Of an output exceeding 37 kW but not exceeding 75 kW | TARIC | ||
| 8501 52 90 10 | For use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 52 90 90 | Other | p/st | 2.7% | TARIC |
| 8501 53 | Of an output exceeding 75 kW | TARIC | ||
| 8501 53 50 | Traction motors | TARIC | ||
| 8501 53 50 10 | Electric drive for motor vehicles, with an output of not more than 315 kW: -with an AC or DC motor with or without transmission, -with or without power electronics | p/st | 2.7% | TARIC |
| 8501 53 50 20 | AC traction motor of the Interior Permanent Magnet Synchronous Motor (IPMSM) type with: -a torque output of 200 Nm or more, but not more than 400 Nm, -a power output of 50 kW or more, but not more than 200 kW , -a rotation speed of no more than 15 000 rpm, for use in the manufacture of electric vehicles | p/st | 2.7% | TARIC |
| 8501 53 50 30 | Permanent magnet synchronous traction motor, with: -a continuous power of 110 kW or more but not more than 180 kW, -a liquid cooled system, -a total length of 500 mm or more but not more than 650 mm, -a total width of 600 mm or more but not more than 700 mm, -a total height of 550 mm or more but not more than 650 mm, -weighing of not more than 350 kg, -3 suspension points | p/st | 2.7% | TARIC |
| 8501 53 50 40 | Permanent magnet traction AC motor, with: -a continuous power of 110 kW or more but not more than 150 kW, -a liquid cooled system, -a total length of 460 mm or more but not more than 590 mm, -a total width of 450 mm or more but not more than 580 mm, -a total height of 490 mm or more but not more than 590 mm, -a weight of not more than 310 kg, -4 mounting points | p/st | 2.7% | TARIC |
| 8501 53 50 50 | Asynchronous traction motor, with: -a continuous power of 140 kW or more but not more than 180 kW, -a liquid cooled system, -a total length of 580 mm or more but not more than 730 mm, -a total width of 550 mm or more but not more than 670 mm, -a total height of 510 mm or more but not more than 630 mm, -with a weight of not more than 390 kg, -with or without reduction gear, -with or without starter generator, -2 mounting points, for use in the manufacture of the electric drive of hybrid buses | p/st | 2.7% | TARIC |
| 8501 53 50 90 | Other | p/st | 2.7% | TARIC |
| Other, of an output | ||||
| 8501 53 81 | Exceeding 75 kW but not exceeding 375 kW | TARIC | ||
| 8501 53 81 10 | Of an output not exceeding 150 kW, for use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 53 81 20 | Of an output exceeding 150 kW, for use in certain types of aircraft | p/st | 2.7% | TARIC |
| 8501 53 81 90 | Other | p/st | 2.7% | TARIC |
| 8501 53 94 | Exceeding 375 kW but not exceeding 750 kW | TARIC | ||
| 8501 53 94 10 | For use in certain types of aircraft | p/st | 2.7% | TARIC |
| 8501 53 94 90 | Other | p/st | 2.7% | TARIC |
| 8501 53 99 | Exceeding 750 kW | TARIC | ||
| 8501 53 99 10 | For use in certain types of aircrafts | p/st | 2.7% | TARIC |
| 8501 53 99 90 | Other | p/st | 2.7% | TARIC |
| AC generators (alternators), other than photovoltaic generators | ||||
| 8501 61 | Of an output not exceeding 75 kVA | TARIC | ||
| 8501 61 20 | Of an output not exceeding 7,5 kVA | TARIC | ||
| 8501 61 20 10 | For use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 61 20 90 | Other | p/st | 2.7% | TARIC |
| 8501 61 80 | Of an output exceeding 7,5 kVA but not exceeding 75 kVA | TARIC | ||
| 8501 61 80 10 | For use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 61 80 99 | Other | p/st | 2.7% | TARIC |
| 8501 62 | Of an output exceeding 75 kVA but not exceeding 375 kVA | TARIC | ||
| 8501 62 00 10 | For use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 62 00 40 | AC, 3-phase generator, with: -a continuous power of 147 kVA or more but not more than 222 kVA, -a continuous torque of 650 Nm or more but not more than 900 Nm, -a maximum working speed of 2700 revolutions per minute (rpm), -a liquid cooled system, -a length of 100 mm or more but not more than 200 mm, -a width of 550 mm or more but not more than 650 mm, -a height of 550 mm or more but not more than 650 mm, -weighing of not more than 150 kg | p/st | 2.7% | TARIC |
| 8501 62 00 98 | Other | p/st | 2.7% | TARIC |
| 8501 63 | Of an output exceeding 375 kVA but not exceeding 750 kVA | TARIC | ||
| 8501 63 00 10 | For use in civil aircraft | p/st | 0% (end-use) | TARIC |
| 8501 63 00 99 | Other | p/st | 2.7% | TARIC |
| 8501 64 00 00 | Of an output exceeding 750 kVA | p/st | 2.7% | TARIC |
| Photovoltaic DC generators | ||||
| 8501 71 00 00 | Of an output not exceeding 50 W | p/st | 2.7% | TARIC |
| 8501 72 00 00 | Of an output exceeding 50 W | p/st | 2.7% | TARIC |
| 8501 80 00 00 | Photovoltaic AC generators | p/st | 2.7% | TARIC |
The table scrolls sideways.
Source: European Commission (DG TAXUD), TARIC and Combined Nomenclature data as extracted on 1 October 2026. Heading 8501 in the TARIC consultation
Only the third-country duty is shown. Not shown: tariff preferences, quotas, suspensions, anti-dumping and other additional duties, import controls and the legal notes. The TARIC consultation lists the measures of each code.
This page is general information, not legal advice and not a classification decision. Tariff texts and rates change: check the publisher's current schedule, and ask the customs authority for a binding ruling where the answer matters.